NCIE-SAN NS0-507 questions and answers|Passcert

Passcert is a greatly reliable company that provides the excellent latest NCIE-SAN NS0-507 questions and answers|Passcert for preparation.Passcert is a professional site which provides information for all IT exams,Passcert is your wise choice to prepare for your NS0-507 test.With the full knowledge of Passcert study guide for Network Appliance NS0-507, Passcert absolutely assures the candidates will pass the NS0-507 exam successfully on their first exam,otherwise, we guarantee to refund your money in full.

Share some Network Appliance NCIE-SAN NS0-507 exam questions and answers below.
You have expanded your ONTAP cluster from two nodes to four nodes and want to allow Linux multipathing software to see the paths to all nodes in the cluster.In this scenario, which statement describes how to accomplish this task? 
A. Add the WWPN to the host igroup then rescan from the host. 
B. Rescan from the host OS and modify the reporting nodes to add the two new nodes. 
C. Modify the reporting nodes to add the two new nodes the rescan from the host OS. 
D. Rescan from the host OS then add the WWPN to the host igroup. 
Answer: C

You need to take a cluster node down for extended maintenance, but you want to the FC LIF to avoid re-zoning the switch fabric. 
In this scenario, which three steps are required to move the FC LIF so it is available on another node? (Choose three.) 
A. Use the network interface migrate command to migrate the new home node and the new home port 
B. Perform a takeover and giveback operation for the new destination node 
C. Use the network interface modify command to modify the new home node and the new home port 
D. Bring the LIF online 
E. Take the LIF offline 
Answer: C,D,E

You have an iSCSI host that is unable to connect to an SVM that is named “svm1” over a LIF that is named “lif1”. The home node and port of lif1 is cl01-01 port e0e. The event log show command displays the error iSCSI: network interface disabled for use; incoming connection discarded.Which command would you use to solve the problem? 
A. Broadcast-domain add-ports –broadcast-domain iscsi –ports cl01-01: e0e 
B. iSCSI interface enable –vserver svm1–lif lif1 
C. Network interface modify –vserver svm1 –lif lif1 –failover-group default 
D. Vserver iscsi create –target-alias svm1 –status-admin up –vserver svm1 
Answer: B

You are asked to create a volume and lun, both of which need to be thin provisioned. 
In this scenario, which two statements are correct? (Choose two.) 
A. Use the lun create command with the space-reserve parameter set to disabled 
B. Use the lun create command with the space-reserve parameter set to enabled 
C. Use the volume create command with the space-guarantee parameter set to none 
D. Use the volume create command with the space-guarantee parameter set to volume 
Answer: A,C

For which two vendor products would the Unified Host Utilities Kit set HBA and CAN parameters? (Choose two.) 
A. Brocade 
B. Cisco 
C. Emulex 
D. Qlogic 
Answer: C,D

According to NetApp best practices, which method should be used for zoning? 
A. Single initiator – multiple targets 
B. Multiple initiator – single target 
C. Single initiator – single target 
D. Multiple initiator – multiple targets 
Answer: C

Referring to the diagram shown in the exhibit, what will happen when the SAS adapter in slot 2 on Node A fails? 



A. Node A will continue to access all drives through the onboard SAS port 0a. 
B. Node A will lose all access to all drives. 
C. Node A will continue to access all drives through the Infiniband connection with Node B. 
D. Node A will shut down until SAS adapter in slot 2 is replaced. 
Answer: A

Within the NetApp Interoperability Matrix Tool (IMT), which three components are supported for the FC SAN storage host solution? (Choose three.) 
A. Host OS 
B. IP switch 
C. ONTAP OS 
D. Netapp Controller Model 
E. Host HBA 
Answer: A,C,E

Where would you find the environment values of controllers and disk shelves (e.g. BTU and watts)? 
A. Interoperability matrix tool (IMT) 
B. Installation and setup instructions poster 
C. Config advisor 
D. Hardware universe 
Answer: D

The Linux Host Utilities 7.1 configures settings for which three protocols? (Choose three.) 
A. NFS 
B. iSCSI 
C. SMB 
D. FCoE 
Answer: A,B,D

Where do you identify the disk shelves and disks that are supported for a specific controller model? 
A. Hardware Universe (HWU) 
B. Interoperability Matrix Tool (IMT) 
C. Disk and Aggregates Power guide 
D. Installation and Setup Instructions poster 
Answer: A

Where would you find the environment values of controllers and disk shelves (e.g. BTU and watts)? 
A. Interoperability matrix tool (IMT) 
B. Installation and setup instructions poster 
C. Config advisor 
D. Hardware universe 
Answer: D

You have expanded your ONTAP cluster from two nodes to four nodes and want to allow Linux multipathing software to see the paths to all nodes in the cluster. 
In this scenario, which statement describes how to accomplish this task? 
A. Add the WWPN to the host igroup then rescan from the host. 
B. Rescan from the host OS and modify the reporting nodes to add the two new nodes. 
C. Modify the reporting nodes to add the two new nodes the rescan from the host OS. 
D. Rescan from the host OS then add the WWPN to the host igroup. 
Answer: C

When a new LUN is allocated, which volume and LUN configuration will use the smallest amount of storage? 
A. Volume guarantee none, fractional reserve 0, space reservation disabled 
B. Volume guarantee none, fractional reserve 0, space reservation enabled 
C. Volume guarantee volume, fractional reserve 100, space reservation enabled 
D. Volume guarantee volume, fractional reserve 100, space reservation enabled 
Answer: A

You have a switch called ¡°NK5-A¡±. The switch is configured with an NP_Port. 
Which switch feature on NK5-A uses NP_Ports to allow for fabric expansion of new FC switches without having to designate additional domain IDs? 
A. NPIV 
B. NPV 
C. FCIP 
D. F_port channel trunking 
Answer: D

After you used Passcert NCIE-SAN NS0-507 questions and answers|Passcert, you still fail in NS0-507 test and then you will get FULL REFUND. This is Passcert's commitment to all candidates. What's more, the excellent dumps can stand the test rather than just talk about it. Passcert NCIE-SAN NS0-507 questions and answers|Passcert can completely stand the test of time. Passcert present accomplishment results from practice of all candidates. Because it is right and reliable, after a long time, Passcert NCIE-SAN NS0-507 questions and answers|Passcert are becoming increasingly popular.

Are you struggling for the NS0-507 exam? Good news, Network Appliance technical experts have collected and certified real questions and answers which are updated to cover the knowledge points and enhance candidates' abilities. With NCIE-SAN NS0-507 questions and answers|Passcert you can pass the exam easily and go further on Network Appliance career path.